The Best Vacuum Liquid Pump

Product Description

Changing engine oil can be messy, time consuming and there is no good way to dispose of old oil. The LiquiVac is a new user friendly and environmentally safe oil changing system. It is fast, convenient and eliminates mess and clean-up. The LiquiVac works by creating a powerful vacuum that draws the used oil out of the engine and into a holding tank for easy disposal to a recycling center. Simply insert the extraction hose into the dipstick tube, pump the handle 40 times, release the hose clamp and LiquiVac extracts the oil directly into its plastic holding tank. Works great for boats, cars, trucks and more. USA dimensions: 16 inch length x 7 inch width x 11 inch height, tank size: 8 gallon, suction hose length 48 inches.

Amazon.com

Changing engine oil can be messy, time consuming and it is difficult to dispose of old oil. The LiquiVac is a user friendly and an environmentally safe oil changing system. It is fast, convenient and eliminates mess and clean-up. The LiquiVac works by creating a powerful vacuum that draws the used oil out of the engine and into a holding tank for easy disposal to a recycling center. Simply insert the extraction hose into the dipstick tube, pump the handle 40 times, open the cap’s valve and LiquiVac extracts the oil directly into its plastic holding tank. It works great for boats, cars, trucks–and small engines too.

Quickly change the oil in large engines–works with small engines too

Cars and Trucks Oil Change

The LiquiVac Oil Changing System for Large Projects and Engines makes car oil changes quick, clean, and easy. This is especially true with hard to access drain plugs found in large engines.

An average car or truck takes approximately 8-10 minutes to extract the oil, and without a mess. The Large Engine/Project Model comes with a special narrow suction hose to fit dipstick tubes of boats, cars, and light trucks. Plus, its tank has an 8 quart capacity allowing the user to make multiple oil changes of small engines too.

Boats

The LiquiVac innovative design makes it easier to change the oil in engines such as boats with inaccessible drain plugs. The Large Engine/Project Model comes with a special narrow suction hose to fit dipstick tubes to make your 4-cycle outboard oil change and inboard oil change easy. Also, don’t forget the LiquiVac makes boat transmission changes very easy.

Small Engines: Lawnmowers, Generators, Power Washers, Snow Throwers, and More

Small engines seem to be the most ignored engines that a consumer owns. This has occurred because there are consumers who have their car oil serviced at the quick lube places. And, have entirely forgotten that all the small engines in their garages need their oil changed too. Unfortunately this neglect can be very costly since these engines run very hard and in dusty conditions, which can lead to dirty, grimy oil and, eventually, engine breakdowns.

With the LiquiVac small engine oil changes are a snap. This vacuum is powerful enough to extract used oil out through the dipstick/fill tube in just 14 seconds. (Extraction time is based on the typical 4-cycle engine containing 1 quart of oil). With this kind of powerful performance and ease of use the LiquiVac Small Engine Model takes maintenance on 4-cycle engines super simple.

Which Model of LiquiVac Is Right for You?

LiquiVac Small Engine Model

Small Engine Model

Small engines seem to be the most ignored engines that a consumer owns. This has occurred because there are consumers who have their car oil serviced at the quick lube places. And, have entirely forgotten that all the small engines in their garages need their oil changed too. Unfortunately this neglect can be very costly since these engines run very hard and in dusty conditions, which can lead to dirty, grimy oil; and, then engine breakdowns.

But, now there’s a simple, fast and clean way to change your lawn and garden equipment’s oil. It’s the LiquiVac Oil Changing System. With the LiquiVac oil changes are a snap. The LiquiVac Small Engine Model works by creating negative pressure, or vacuum power in the tank by pumping the tank handle. Each pump stroke takes air out of the tank creating a vacuum. Just 20 quick pump strokes creates vacuum power in the tank. This vacuum is powerful enough to extract used oil out through the dipstick/fill tube with the release of the suction hose clamp, in just 14 seconds. (Extraction time is based on the typical 4-cycle engine containing 1 quart of oil). With this kind of powerful performance and ease of use the LiquiVac Small Engine Model takes maintenance on 4-cycle engines very easy. Perfect for lawn mowers, lawn & garden tractors, tillers, generators, snow throwers, ATVs and outboard motors as well as.

LiquiVac Large Project/Engine Model

Large Project/Engine Model

It is called the Large Project/Engine Model for a reason. Its 8 quarts capacity is large enough to handle several oil changes at one time, without recycling/emptying it. For example you can change your boat engine and several small engines in one session. Because of this, many do-it-yourself people love to knock out their oil change projects in one fell swoop. They can do it fast, without the mess. Plus, the Large Project and Large Engine Model works great for large engines such as hard to change boats (inboards and outboards), trucks, and cars too. It is also very handy for to change transmission oil and hydraulic fluids too.

Specification:
Rated Voltage: DC 12V
Rated Power: 60W
Maximum Pressure: Max. 0.8MPA
Maximum Flow: 5L/min
Color: Black
Pump Diameter: Approx. 4.8cm/1.89″
Length: Approx. 14.5cm/5.7″
Outlet pipe size(Dia.*L): Approx. 10mm*137cm
Inlet pipe diameter: Approx. 8mm,6 mm ; Length: Approx. 110cm/43.3″

Package include:
1x Oil Pump
1x 11mm Outlet PVC pipe
1x 6mm Nylon pipe
1x 5mm Brass pipe

How to use:
1.Start to run the car engine for a while, when oil temperature turns to be about 50 degrees, start pumping oil.
2.Then connect the pump to the power, run it for a while, and observe whether the inlet and outlet is normal.
3.Next,open the filler cap,get dipstick out, force the tube into the bottom of the joint, until the tube does not move;
then put the inlet pipe from the oil dipstick into in end (the tube into the bottom of the tank, the bottom concave place, in order to pump the oil completely);
as no oil or pumping up very slowly or intermittently, it is generally caused by loose pipes and fittings. You have to install the pipes and fittings again.
4.After oil pumping, remove the tube, and then run the pump for a while, pump the remaining oil inside the pumping clean, or pump water for a while until the pump head gets clean.
5.If you have not used it for a long time, it may have no suction, then just pour the water in the pump, and run the pump for a few minutes until the air is all out.
Note:
If you want to connect this pump to AC power, you will need a power converter.
Make sure the engine up to operating temperature!

The VaygWay 3-in-1 Hand Siphon Emergency Vehicle Pump is constructed out of Premium Quality material to provide you with the Strongest most Durable pump available. It has rubber hoses that can withstand chemical reaction brought about the varying fluids introduced to them. This item will last superbly year after year. The VaygWay 3-in-1 Hand Siphon Emergency Vehicle Pump is best for emergencies. When you’re stuck with an empty tank The VaygWay 3-in-1 Hand Siphon Emergency Vehicle Pump enables you to Quickly and Easily pump the gas from the carry on container to the gas tank. That will comfortably take you to the nearest gas station where you can refuel once again.

The VaygWay 3-in-1 Hand Siphon Emergency Vehicle Pump is a most important and practical accessory to always have in your car. It pumps Gas Oil or any Liquid into your car as well as Air into inflatable objects such as rafts, tires, swimming pools etc. When you’re stuck with an empty tank The VaygWay 3-in-1 Hand Siphon Emergency Vehicle Pump enables you to quickly and Easily Pump the gas from the carry on container to the gas tank. That will comfortably take you to the nearest gas station where you can refuel once again.

YOU WILL NEVER GO WRONG BY CHOOSING VAYGWAY 3-IN-1 HAND SIPHON EMERGENCY VEHICLE PUMP!!!!!!

NestEcho lab vacuum filtration pump is working for the Laboratory Vacuum Filtration Distillation Apparatus to filter the liquid quicklier which can help to save a lot time.

The working voltage of NestEcho laboratory filtration pump is 110-120V and the working HZ is 60HZ so It is made for USA market.(If you want to use this product in other country, please check the working voltage and working HZ to make sure whether it is suitable for the country you want to use for or not.)

There are three different tubing for connecting to different size nozzle of Laboratory Vacuum Filtration Distillation Apparatus. one unit 4mm ID x 5mm OD Transparent tube; one unit 5mm ID x 7mm OD black tubing; one unit 6mm ID x 9mm OD yellow tubing; The tubing is flexible so Nestecho lab vacuum filtration pump can be suitable for different lab filter bottle in the market.

The transparent tubing need to be pluged to the lab vacuum filtration and connect the black silicone tubing to the lab vacuum filtration and then turn the lab filter pump on in order to let the lab vacuum pump work.(the yellow tubing can be connected to the black tubing in order to connect to big size nozzle of laboratory vacuum filtration distillation apparatus)

The lab vacuum pump product is made of plastic shell,Copper wire inside part and four Shockproof rubber base etc. The plastic shell can avoid rust.copper wire inside part makes the product more durable.The shockproof rubber base can reduce noise.You can barely hear the noise when the product is working.

The Way To Use：

1. Keep the arrow on the sphere down

2. Insert the upper tube into the fuel tank

3. Insert the lower tube into the container

4. Pinch the rubber ball 3-5 times

5. Liquid outflow

Warm Tips:

1. The fluid you are trying to extract has to be HIGHER than the influent bucket.

2. There’s a mark “arrow” on the surface of hand pump.Please keep the arrow down before pumping.

3. The fitting end must kept inside of the fluid not just on the surface.

4. To extract the oil in the fuel tank of the car, there must be no anti-pumping filter in the fuel tank. 

Package List:

1 x good suction sphere

1 x Hose(L:2m, D: 21mm. Needs to be cut customized and installed depending on your needs.)

2 x valve clips

Flow Rate: 10L/Min